Key takeaways
- P0502 body height and catalog overall height describe different dimensions. A body taller than the available assembled drop cannot be made to fit simply by shortening the suspension.
- For an illustrative 1400 mm maximum assembled drop, the listed P0502-4A and P0502-5A bodies are already too tall. P0502-2A and P0502-3A pass only the body-height screen; a complete fitting within 1400 mm remains to be confirmed.
- The catalog overall heights are listed values, not a stated minimum, maximum or adjustment range. Do not derive a usable cable length by subtracting body height.
Check the body before relying on a shorter suspension
Start P0502 selection with the height of the rigid lighting body. If that body alone exceeds the space allowed for the complete hanging fitting, a shorter suspension cannot solve the mismatch. When the body fits, the next decision is whether the manufacturer can supply a complete assembly within the required drop.
The current P0502 listing gives both body height and overall height for four actual models. It does not state a minimum installed drop, an adjustment range or permission to cut the suspension on site. Treat the listed overall height as a catalog dimension until the supplier confirms the assembly and its measurement points.
Existing Lumseq AI design illustration labelled P0502-2A. The setting and panel labelled Installed Effect are design references, not a photographed installation or dimensional evidence. The product page asks for manufacturer confirmation of the illustrated identity. Full original poster retained.
Keep the two height columns tied to the exact model
All four listed P0502 configurations have a 445 mm diameter. Their body height, overall height and power change together as shown below. These are current first-party catalog values; they are not installation approvals or measured lighting performance.
The shared listing specifies glass and aluminium, Smoky Gray finish, 3000K, AC 90–260V, 50/60Hz and IP20. Keep these details with the selected model when requesting a quote. A shared diameter or finish does not make the four models vertically interchangeable.
| Listed model | Body height | Catalog overall height | Listed power |
|---|---|---|---|
| P0502-2A | 613 mm | 1600 mm | 25 W |
| P0502-3A | 1017 mm | 2000 mm | 30 W |
| P0502-4A | 1421 mm | 2435 mm | 40 W |
| P0502-5A | 1825 mm | 2800 mm | 50 W |
Define the available drop from agreed reference points
For this screening method, the available assembled drop is the largest permitted distance from the agreed ceiling-fixing reference to the lowest point of the fitting. The project team must establish that envelope from the actual ceiling, furniture or circulation area and applicable requirements. It is not simply the room height.
Mark both reference points on a section drawing. Ask the supplier to use the same reference when showing the proposed overall drop. Include the canopy, suspension and body in the complete assembly; leave structural support and installation details for the qualified project team. Check the separate 445 mm diameter against the available horizontal space.
This turns a request such as “Can this pendant be shortened?” into a defined question: “Can this exact model be supplied with the complete assembly ending within this marked envelope?”
Worked screen: a project permits 1400 mm in total
Assume, solely for this example, that the project team has already set a maximum assembled drop of 1400 mm between the agreed points. This is an illustrative project input, not a recommended clearance, code value or P0502 adjustment limit.
P0502-4A and P0502-5A fail immediately on body height: their listed bodies are 1421 mm and 1825 mm. Both exceed the entire 1400 mm envelope before any canopy or suspension is added. Retaining those bodies while shortening only the suspension cannot resolve that geometry.
P0502-2A and P0502-3A remain candidates because their bodies are shorter than 1400 mm. The differences, 787 mm and 383 mm, are only the space left above the body within this hypothetical envelope. They are not permissible cable lengths, allowances to cut, or confirmed suspension settings.
The catalog overall heights for these two candidates are still 1600 mm and 2000 mm, so neither listed overall dimension satisfies the example as written. Obtain a manufacturer-supported assembly drawing at or below 1400 mm before accepting either. If its minimum achievable assembly exceeds the available drop, choose a different fitting geometry.
| Model | Body-height screen at 1400 mm | Decision |
|---|---|---|
| P0502-2A | 613 mm body; 787 mm remains above it | Conditional candidate; complete assembly unconfirmed |
| P0502-3A | 1017 mm body; 383 mm remains above it | Conditional candidate; complete assembly unconfirmed |
| P0502-4A | 1421 mm body exceeds total envelope by 21 mm | Reject this body for the stated envelope |
| P0502-5A | 1825 mm body exceeds total envelope by 425 mm | Reject this body for the stated envelope |
Quote a required assembly, not an assumed cable alteration
A useful enquiry can read: “Please review P0502-2A, configuration jyv-816899dec143, listed body H613 mm, diameter 445 mm, 25 W, Smoky Gray, 3000K. Our maximum assembled drop is [enter project dimension] from [marked ceiling reference] to [lowest permitted point]. Please show the proposed complete drop, canopy and suspension arrangement on the attached section. Quantity: [enter quantity].”
Ask the manufacturer to state the achievable drop range and any approved adjustment method for the offered assembly. Keep any altered body or different model as a separately identified proposal. Do not ask an installer to improvise shortening from the marketing image or from the difference between two catalog dimensions.
Send Lumseq the chosen model and a marked vertical section. The first selection decision is geometric: eliminate bodies that cannot fit, then resolve the complete assembly for the remaining candidates. Lighting output and visual sample approval remain separate decisions.
Frequently asked questions
Questions buyers ask
Can I subtract body height from overall height to obtain the cable length?
No. The two catalog values do not identify every included component or the precise measurement points. Their difference may include parts of the suspension or canopy, and does not establish an adjustable or cuttable cable length. Request a dimensioned assembly drawing and the manufacturer’s supported adjustment method for the exact model.
Sources and references
Lumseq Lantern Stacked Pendant Light — current configuration comparisonLumseq public product catalog — P0502 Lantern familyTalk to the product team
Planning an OEM or commercial lighting order?
Send your application, specification and destination market. We will help narrow the product and sample options.
Discuss on WhatsApp